STUPIDSID
Solve any one question.Q1(a,b) Q2(a,b)
1(a)
State the different types of moulding sands. With a sketch explain the method ti test the porosity of a moulding sand.
6 M
1(b)
Using Chevorinor's rule find the ratio solidification time for a cube shape casting to sphere shape casting. The volume of the cube shape casting (having side 'a') and sphere shape casting (radius 'r') is 1000 cm3. Assume value of mould constant is same for both cube and spehere shaped castings.
6 M
2(a)
State an importance of flow stress and srain rate in metal forming. Also, show with a plot the effect of temperature on yield strength and ductibility of material in metal forming.
6 M
2(b)
A billet having initial diameter of 50 mm is directly extruded to a diameter of 30 mm. The length of the billet is 100 mm. For the work metal strength coefficient 'K' is 600 MPa and strain hardening exponent 'n' is 0.1. Take the values of the constants in Johnson formula 'a' and 'b' as 0.8 and 1.3 repectively. Pressure at length of billet is equal to 75 mm. Assume shape factor as unity.
6 M
Solve any one question from Q.3(a,b) & Q.4(a,b)
3(a)
With a neat sketch explain the working principle of pressure thermoforming.
6 M
3(b)
With a schematic write down the steps to be followed in compression moulding for thermoplastics.
6 M
4(a)
State the six points of differences between A.C. welding and D.C. welding.
6 M
4(b)
With neat sketches state the characteristics of different types of gas flames.
6 M
Solve any one question from Q.5(a,b) & Q.6(a,b)
5(a)
Name the different types of dies according to the type of press operation and method operation that are used in sheet metal working. Also, draw a neat sketch of compound die where in punching and blanking operation are performed simultaneously.
6 M
5(b)
Design a strip layout for manufacturing a mild steel component as shown in figure. The thickness of the component is 1 mm. Take ultimate shear stress value as 200 N/mm2. Also find the percentage utilization, centre of pressure and press capacity. Comment on how to increases the percentage utilization of the sheet. The dimesnsions shown in figure for the component are in mm:
!mage
!mage
7 M
6(a)
Explain with sketches various types of pilots used in sheet metal working.
6 M
6(b)
A cup of internal diameter 60mm, height 80 mm is to be drawn from a 2 mm cold rolled steel. The corner radius for cylindrical cup is 1.8 mm. Percentage reduction permitted in the first draw is 50% and in the second, third and fourth draw is 30%, 20% and 15% repectively. Consider trimming allowance of 3.2 mm for each 25 mm of cup diameter. Find size of the blank, number of draws required, punch and die dimensions for each draw. Also draw sectional view of die block showing different dimensions for last draw. Consider value of punch and die clearance as 1.15 times thickness of sheet.
7 M
Solve any one question from Q.7(a,b) & Q.8(a,b)
7(a)
State the importance of lathe centres, lathe dogs/ carrier and mandrels while machining on lathe.
6 M
7(b)
A hollow workpiece of 80 mm diameter nad 150 mm length is to be turned down to 72 mm for length. The maximum aloowable depth of cut is 1 mm. Assume feed as 0.3 mm/rev and cutting speed as a 3 metre per seconds. If the apporach length is 30 mm and over travel is 20 mm then calculate the machining time. If feed changes to 0.5 mm/seconds keeping the cutting speed as same given above, then calculate the machining time and percentage change in machining time due to change in feed from 0.3 mm/ rev to 0.5 mm/second.
7 M
8(a)
What is all geared head stock? State its advantages limitations in comparison to belt driven lathes.
6 M
8(b)
Calculate the change gears for cutting three start right hand threads of 1.8mm pitch on a lathe having 4 mm pitch of lead screw. Available gears are 20 to 120 teeth in steps of 5 teeth. Also suggest two more alternative solutions for change gears other than obtained in the earlier step. Sketch the gear train and suggest what modification is required forcutting left hand threads?
7 M
More question papers from Manufacturing Process 1